Expecting to get a good job without studying hard is like expecting to win a marathon without running it.
--Your friends at LectureNotes

Note for Power System Engineering II - PSE2 By MD WESH KARNI

  • Power System Engineering II - PSE2
  • Note
  • 5 Topics
  • 15 Offline Downloads
  • Uploaded 11 months ago
Md Wesh Karni
Md Wesh Karni
0 User(s)
Download PDFOrder Printed Copy

Share it with your friends

Leave your Comments

Text from page-1

VEER SURENDRA SAI UNIVERSITY OF TECHNOLOGY BURLA, ODISHA, INDIA DEPARTMENT OF ELECTRICAL ENGINEERING Lecture Notes on Power System Engineering II Subject Code:BEE1604 6th Semester B.Tech. (Electrical & Electronics Engineering)

Text from page-2

Disclaimer This document does not claim any originality and cannot be used as a substitute for prescribed textbooks. The information presented here is merely a collection by the committee members for their respective teaching assignments. Various sources as mentioned at the end of the document as well as freely available material from internet were consulted for preparing this document. The ownership of the information lies with the respective authors or institutions. Further, this document is not intended to be used for commercial purpose and the committee members are not accountable for any issues, legal or otherwise, arising out of use of this document. The committee members make no representations or warranties with respect to the accuracy or completeness of the contents of this document and specifically disclaim any implied warranties of merchantability or fitness for a particular purpose. The committee members shall be liable for any loss of profit or any other commercial damages, including but not limited to special, incidental, consequential, or other damages.

Text from page-3

(6 SEMESTER) POWER SYSTEM-II (3-1-0) MODULE-I (10 HOURS) Lines Constants: Resistance, inductance and capacitance of single and three phase lines with symmetrical and unsymmetrical spacing transposition, charging current, skin effect and proximity effect, Performance of transmission Lines: Analysis of short, medium and long lines, equivalentcircuit, representation of the lines and calculation of transmission parameters, Power flow through transmission line, Power circle diagram, Series and shunt compensation. MODULE-II (10 HOURS) Corona: Power loss due to corona, practical importance of corona, use of bundled conductors in E.H.V. transmission lines and its advantages, Overhead line Insulators, voltage distribution in suspension type insulators, string efficiency, grading. Sag and stress calculation of overhead conductors, vibration dampers Under Ground Cable: Type and construction, grading of cables, capacitance in 3 core cables and dielectric loss in cables. MODULE-III (10 HOURS) Definition of the load flow problem, Network model formulation, A load flow sample study,Computational aspect of the load flow problem. Gauss siedel and Newton Raphson method for power flow fast decoupled load flow, On load tap changing transformer and block regulating transformer, effects of regulating transformers. MODULE-IV (10 HOURS) Economic Operation of Power System: Distribution offload between units within a plant, Transmission losses as function of plant generation, Calculation of loss coefficients, Distribution of loads between plants with special reference to steam and hydel plants, Automatic load dispatching. Introduction to Flexible AC Transmission System (FACTS), SVC, TCSC, SSSC, STATCOM and UPFC BOOKS [1]. John J Grainger, W. D. Stevenson, “Power System Analysis”, TMH Publication [2]. I. J. Nagrath & D. P. Kothari, “Power System Analysis”, TMH Publication

Text from page-4

MODULE I Transmission line Conductors Commonly used conductor materials: The most commonly used conductor materials for over head lines are copper, aluminium, steelcored aluminium, galvanised steel and cadmium copper. The choice of a particular material will depend upon the cost, the required electrical and mechanical properties and the local conditions. All conductors used for overhead lines are preferably stranded in order to increase the flexibility.In stranded conductors, there is generally one central wire and round this, successive layers of wires containing 6, 12, 18, 24 ...... wires. Thus, if there are n layers, the total number of individual wires is 3n(n + 1) + 1. In the manufacture of stranded conductors, the consecutive layers of wires are twisted or spiralled in opposite directions so that layers are bound together. Types of Conductors 1. Copper. Copper is an ideal material for overhead lines owing to its high electrical conductivity and greater tensile strength. It is always used in the hard drawn form as stranded conductor. Although hard drawing decreases the electrical conductivity slightly yet it increases the tensile strength considerably. Copper has high current density i.e., the current carrying capacity of copper per unit of Xsectional area is quite large. This leads to two advantages. Firstly, smaller X-sectional area of conductor is required and secondly, the area offered by the conductor to wind loads is reduced. Moreover, this metal is quite homogeneous, durable and has high scrap value. There is hardly any doubt that copper is an ideal material for transmission and distribution of electric power. However, due to its higher cost and non-availability, it is rarely used for these purposes. Now-a-days the trend is to use aluminium in place of copper. 2. Aluminium. Aluminium is cheap and light as compared to copper but it has much smaller conductivity and tensile strength. The relative comparison of the two materials is briefed below: (i) The conductivity of aluminium is 60% that of copper. The smaller conductivity of aluminium means that for any particular transmission efficiency, the X-sectional area of conductor must be larger in aluminium than in copper. For the same resistance, the diameter of aluminium

Lecture Notes