×
Study for the day when you don't have to worry about price tags.
--Your friends at LectureNotes
Close

Engineering Chemistry-2

by Anna SuperkingsAnna Superkings
Type: NoteInstitute: Anna university Offline Downloads: 131Views: 3806Uploaded: 4 months ago

Share it with your friends

Suggested Materials

Leave your Comments

Contributors

Anna Superkings
Anna Superkings
Unit I Water Technology 1.1 INTRODUCTION Water is essential for the existence of human beings, animals and plants. Though 80% of the earth‟s surface is occupied by water, less than 1% of the water is available for ready use. The main sources of water are Rain rivers and lakes (surface water) wells and springs (ground water) sea water Among the above sources of water, rain water is the purest form of water but it is very difficult to collect whereas sea water is the most impure form. Thus, surface and ground water are normally used for industrial and domestic purposes. Such water must be free from undesirable impurities. “The process of removing all types of impurities from water and making it fit for domestic or industrial purposes are called water treatment.” Before treating water one must know the nature as well as the amount of impurities. 1.2 HARD WATER AND SOFT WATER Hard Water “Water which does not produce lather with soap solution, but produces white precipitate is called hard water”. This is due to the presence of dissolved Ca and Mg salts. 2C17 H 35 COONa + Ca ++ → (C17 H 35 COO) 2 Ca +2Na+ Water soluble Water insoluble Soft Water “Water which produces lather readily with soap solution is called soft water.” This is due to the absence of Ca and Mg salts. BOILER FEED WATER In Industry, one of the chief uses of water is generation of steam by boilers. The water fed into the boiler for the production of steam is called boiler feed water. Requirements of boiler feed water It should have zero hardness. It must be free from dissolved gases like O2, CO2, etc. It should be free from suspended impurities. It should be free from dissolved salts and alkalinity.
It should be free from turbidity and oil. It should be free from hardness causing and scale forming constituents like Ca and Mg salts. FORMATION OF DEPOSITS IN STEAM BOILERS AND HEAT EXCHANGERS 1.5.1 Sludge and Scale formation in boilers In a boiler, water is continuously converted into steam. Due to this continuous evaporation of water, the concentration of soluble matters increases progressively. Then the salts separating out from the solution in the order of their solubility, the lease soluble ones separating out first. (i) Sludge If the precipitate is loose and slimy it is called sludges. Sludges are formed by substances like MgCl2, MgCO3, MgSO4 and CaCl2. They have greater solubilities in hot water than cold water. Scale 1) If the precipitate forms hard and adherent coating on the inner walls of the boiler, it is called scale. 2) Scales are formed by substances like Ca (HCO3)2, CaSO4 and Mg (OH) 2. 1.5.2 Disadvantages (i) Wastage of fuels Scales have a low thermal conductivity, so the rate of heat transfer from boiler to inside water is greatly decreased. In order to provide a supply of heat to water, excessive or over-heating is done. This causes increase in fuel consumption. The wastage of fuel depends upon the thickness and the nature of scale. (ii) Decrease in efficiency Scales sometimes deposit in the valves and condensers of the boiler and choke them partially. This results in decrease in efficiency of the boiler.
Boiler explosion When thick scales crack due to uneven expansion, the water comes suddenly in contact with over-heated iron plates. This causes in formation of a large amount of steam suddenly. So sudden high-pressure is developed, which may even cause explosion of the boiler. 1.6 PREVENTION OF SCALE FORMATION (OR) SOFTENING OF HARD WATER The process of removing hardness – producing salts from water is known as softening or conditioning of water. Since water is a source for industrial purpose. It is mandatory to soften water to make it free from hardness producing substances, suspended impurities and dissolved gases, etc. Softening of water can be done by two methods. External treatment Internal treatment. EXTERNAL TREATMENT It involves the removal of hardness producing salts from the water before feeding into the boiler. The external treatment can be done by the following methods. Zeolite (or) Permutit process Zeolite (or) Permutit process Zeolites are naturally occuring hydrated sodium aluminosilicate minerals. The chemical formula is Na2O.Al2O3.XSiO2.YH2O. The synthetic form of zeolite is called permutit and is represented by Na2Ze. In this process the hard water is allowed to perlocate through sodium zeolite. The sodium ions which are loosely held in this compound are replaced by Ca2+ and Mg2+ ions. When zeolite comes in contact with hard water, it exchanges its sodium ions with calcium and magnesium ions of hard water to form calcium and magnesium zeolites. As sodium ions do not give any hardness to water, the effluent will be soft. The exhausted zeolite is again regenerated by treated with 5 to 10 percent of sodium chloride solution. CaZe + 2 NaCl → Na2Ze + CaCl2 MgZe + 2 NaCl → Na2Ze + MgCl2
Advantages No sludge is formed during this process. Water of nearly zero hardness is obtained. This method is very cheap because the generated permutit can be used again. The equipment used is compact and occupies a small space. Its operation is also easy. The process can be made automatic and continuous. Disadvantages This process cannot be used for turbid and acidic water as they will destroy the zeolite bed. This treatment replaces only the cations, leaving all the anions like (HCO3)– and (CO3)2– in the soft water. When such water is boiled in boilers, CO2 is liberated. Free CO2 is weakly acidic in nature and extremely corrosive to boiler metal. Na2CO3 + H2O→2NaOH + CO2 Due to the formation of sodium hydroxide, the water becomes alkaline and can cause cause caustic embrittlement. Water containing Fe, Mn cannot be treated, because regeneration is very difficult. This process cannot be used for softening brackish water. Because brackish water also contains Na+ ions. So, the ions exchange reaction will not take place. DEMINERALIZATION 1.8.1 Ion exchange or Demineralisation process Ion exchange or demineralisation process removes almost all the ions (both anions and cations) present in the hard water. The soft water, produced by lime-soda and zeolite processes, does not contain hardness producing Ca2+ and Mg2+ ions, but it will contain other ions like Na+, K+, SO42–, Cl– etc., On the other hand demineralised (DM) water does not contain both anions and cations. Thus a soft water is not demineralised water whereas demineralised water is soft water. This process is carried out by using ion exchange resins, which are long chain, cross linked, insoluble organic polymers with a micro process structure. The functional groups attached to the chains are responsible for the ion exchanging properties.

Lecture Notes