×

Close

- Structural Analysis-2 - SA-2
- Note
**1129 Views**- 20 Offline Downloads
- Uploaded 10 months ago

LECTURE NOTE COURSE CODE-BCE 306 STRUCTURAL ANALYSIS 2 1 Under Revision

BCE 306 - STRUCTURAL ANALYSIS –II Module – I Introduction to Force and Displacement methods of structural analysis, Analysis of continuous beam and plane frame by slope deflection method and moment distribution method. Module –II Analysis of continuous beam and simple portals by Kani’s method, Analysis of two pinned and fixed arches with dead and live loads, suspension cable with two pinned stiffening girders. Module – III Plastic Analysis: Plastic modulus, shear factor, plastic moment of resistance, load factor, plastic analysis of continuous beam and simple rectangular portals, Application of upper and lower bound theorems Module – IV Matrix method of analysis: flexibility and stiffness method, Application to simple trusses and beam Reference Books 1. Indeterminate Structures by J.S. Kenney 2. Indeterminate Structures By C.K. Wang. 3. Matrix methods of Structural Analysis By Pandit and Gupta 2 Under Revision

INTRODUCTION TO FORCE STRUCTURAL ANALYSIS AND DISPLACEMENT METHODS OF Since twentieth century, indeterminate structures are being widely used for its obvious merits. It may be recalled that, in the case of indeterminate structures either the reactions or the internal forces cannot be determined from equations of statics alone. In such structures, the number of reactions or the number of internal forces exceeds the number of static equilibrium equations. In addition to equilibrium equations, compatibility equations are used to evaluate the unknown reactions and internal forces in statically indeterminate structure. In the analysis of indeterminate structure it is necessary to satisfy the equilibrium equations (implying that the structure is in equilibrium) compatibility equations (requirement if for assuring the continuity of the structure without any breaks) and force displacement equations (the way in which displacement are related to forces). We have two distinct method of analysis for statically indeterminate structure depending upon how the above equations are satisfied: 1. Force method of analysis 2. Displacement method of analysis In the force method of analysis,primary unknown are forces.In this method compatibility equations are written for displacement and rotations (which are calculated by force displacement equations). Solving these equations, redundant forces are calculated. Once the redundant forces are calculated, the remaining reactions are evaluated by equations of equilibrium. In the displacement method of analysis,the primary unknowns are the displacements. In this method, first force -displacement relations are computed and subsequently equations are written satisfying the equilibrium conditions of the structure. After determining the unknown displacements, the other forces are calculated satisfying the compatibility conditions and force displacement relations The displacement-based method is amenable to computer programming and hence the method is being widely used in the modern day structural analysis. DIFFERENCE BETWEEN FORCE & DISPLACEMENT METHODS FORCE METHODS 1. 2. 3. 4. DISPLACEMENT METHODS 1. 2. 3. 4. Method of consistent deformation Theorem of least work Column analogy method Flexibility matrix method Types of indeterminacy- static indeterminacy Slope deflection method Moment distribution method Kani’s method Stiffness matrix method Types of indeterminacy indeterminacy- kinematic 4 Under Revision

Governing equations-compatibility equations Force displacement matrix relations- Governing equations-equilibrium equations flexibility Force displacement relations- stiffness matrix All displacement methods follow the above general procedure. The Slope-deflection and moment distribution methods were extensively used for many years before the computer era. In the displacement method of analysis, primary unknowns are joint displacements which are commonly referred to as the degrees of freedom of the structure. It is necessary to consider all the independent degrees of freedom while writing the equilibrium equations.These degrees of freedom are specified at supports, joints and at the free ends. SLOPE DEFLECTION METHOD In the slope-deflection method, the relationship is established between moments at the ends of the members and the corresponding rotations and displacements. The slope-deflection method can be used to analyze statically determinate and indeterminate beams and frames. In this method it is assumed that all deformations are due to bending only. In other words deformations due to axial forces are neglected. In the force method of analysis compatibility equations are written in terms of unknown reactions. It must be noted that all the unknown reactions appear in each of the compatibility equations making it difficult to solve resulting equations. The slope-deflection equations are not that lengthy in comparison. The basic idea of the slope deflection method is to write the equilibrium equations for each node in terms of the deflections and rotations. Solve for the generalized displacements. Using moment-displacement relations, moments are then known. The structure is thus reduced to a determinate structure. The slope-deflection method was originally developed by Heinrich Manderla and Otto Mohr for computing secondary stresses in trusses. The method as used today was presented by G.A.Maney in 1915 for analyzing rigid jointed structures. Fundamental Slope-Deflection Equations: The slope deflection method is so named as it relates the unknown slopes and deflections to the applied load on a structure. In order to develop general form of slope deflection equations, we will consider the typical span AB of a continuous beam which is subjected to arbitrary loading and has a constant EI. We wish to relate the beams internal end moments in terms of its three degrees of freedom, namely its angular displacements and linear displacement which could be caused by relative settlements between the supports. Since we will be developing a formula, moments and angular displacements will be considered positive, when they act clockwise on the span. The linear displacement will be considered positive since this displacement causes the chord of the span and the span’s chord angle to rotate clockwise. The slope deflection equations can be obtained by 5 Under Revision

## Leave your Comments