DC Step Up Voltage Converter Description. A simple DC to DC step up voltage converter using LM2700 is shown here. LM2700 is a step up switching converter that has a 3.6A, 80 M ohm internal switch. It can be operated at 600 kHz or 1.25MHz switching frequency. In the circuit LM2700 is wired in order to produce 8V DC output from a 3V input at a switching frequency of 600MHz. Resistor network consisting of R2 and R3 sets the output voltage. Capacitor C1 and C2 are meant for input voltage filter for reducing ripple and noise. FSCLT pin (pin13) is connected to ground in order to run the IC at 600KHz switching frequency. Connecting this pin to Vin will make the IC run at 1.25MHz. Step up voltage converter Circuit diagram. Step up voltage converter circuit diagram
12V/120mA switch mode power supply circuit. Transformer less switch mode power supplies have become very popular these days. The circuit shown below is of a 12V/120mA output, 85 to 230V AC input transformerless switch mode power supply using LNK304 IC. Applications of a power supply based on this IC includes hand held devices, timers, small appliances, LED drivers, industrial gadgets etc. LNK304 is a low component count, efficient off-line switcher IC that can support buck, buck-boost and flyback topologies. The IC has a built in auto start circuit for short circuit and open loop fault protection. Other features of LNK304 includes low temperature variation, thermal shut down,high break down voltage, good line & load regulation, high band width , wide input voltage range (85 to 230V AC) etc. In general the LNK304 has a better performance when compared to the many other discrete buck regulators. LNK304 pin configuration and typical application The pin configuration and the typical application diagram of LNK304 are shown above. Drain (D) pin the drain connection of the built in power MOSFET. The external by pass capacitor (0.1uF) is connected to the BYPASS (BP) terminal. FEEDBACK (FB) pin
controls the switching of the built in power MOSFET. A current above than 49uA delivered to this pin will inhibit the switching. The internal power MOSFETs source is connected to the SOURCE (S) pin. LNK304 based switch mode power supply circuit. 12V /120 switch mode power supply circuit The circuit diagram of a practical 12V/120mA transformerless switch mode power supply is shown above. Resistor R1, capacitors C1 and C2, diodes D1 and D2 and inductor L1 forms the input stage. D1 and D2 forms the rectifier section while C1 and C2 are input filters. Resistor R1 which is a fusible resistor limits the inrush current, increases differential mode noise attenuation and also serves as an input safety fuse. The next stage is the regulator stage which consists of IC LNK304, diodes D3 and D4, capacitors C3, C4 and C5, resistors R3, R4 and R5 and inductor L2. D3 is the freewheeling diode while L2 is the output choke. C5 is the output filter capacitor which limits the output ripple voltage to a value as low as possible. The IC LNK304 is so configured that the power supply operated in the most
discontinuous mode and that’s why a fast recovery diode (UF4005) is used as the freewheeling diode (D3). UF4005 has a reverse recovery time of around 75nS and it is well enough for the given situation. The voltage drop across diodes D3 and D4 are practically same and so the voltage across C4 tracks the output voltage and this voltage is picked by the network comprising of resistors R2, R3 and is fed to the feedback pin. R2 and R3 sets the output voltage and for 12V output the voltage at the feedback pin must be 1.65V DC. The circuit attains regulation by skipping the switching cycles. When the output voltage rise, the current at the feedback pin also rises and when the current rises above the threshold value, subsequent cycles are skipped until the current at the feedback pin goes below the threshold and thus a constant output voltage is maintained. The IC will auto restart if no cycles are skipped during a 50mS time period and this limits the maximum output power to 6% of the maximum over load power. That’s how over load protection is attained. Resistor R4 serves as a small preload which nullifies the effects of tracking error. Notes. ▪ Assemble the circuit on a good quality PCB. ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ LNK304 is a very high efficiency switching regulator IC that has a hand full of applications. LNK304 is commonly available in SMD package (DIP is also available) and care must be taken while soldering it. D1 and D2 are standard 1N4007 silicon rectifier diodes. D3 (UF4005) is a fast recovery diode. D4 (1N4005GP) is a glass passivated diode. C3 can be a ceramic capacitor. C1,C2 and C4 are polyester capacitors. C5 can be electrolytic or polyester capacitor. Voltage ratings of the capacitors are shown in the circuit diagram. R1 is a fusible, fire proof resistor. Maximum possible output current is 120mA. Input voltage range is 85 to 230V AC. Few switching regulator circuits that may be useful to you. 1. 3A Switching regulator : A simple 3 ampere switching regulator circuit designed based on the popular LM317K IC. Output voltage range is 1.8 to 32V DC and it can be adjusted using a POT. Input voltage range is from 8 to 35V DC.